Help

How to measure belts

Identify and measure V-belts, wedge belts, timing belts and ribbed belts, so you order the right replacement first time.

1.Read the code first

Almost every belt has a reference printed or moulded on its back. If you can read it, it's more reliable than any tape measure, because used belts stretch and wear. Wipe the belt clean and check its full length, as the print is often faint on older belts.

Example codeBelt typeWhat it means
A42Classic V-beltA section, 42 inch inside length
SPZ1000Wedge beltSPZ section, 1000 mm pitch (datum) length
3V500Narrow V-belt (imperial)3V section, 50.0 inch outside length
800-8M-20HTD timing belt800 mm pitch length, 8 mm tooth pitch, 20 mm wide
390L100Imperial timing belt39.0 inch pitch length, L pitch, 1.00 inch wide
6PK1200Ribbed (poly-V) belt6 ribs, PK profile, 1200 mm effective length

Got a code? Type it into the part number search. If it's partly worn off, send us what you can read with a photo and we'll help match it.

2.Identify the belt type

Look at the belt's cross-section and underside. Each type is measured differently, so work this out first.

Classic V-beltTrapezoid profile, wider than it is deep. Sections Z, A, B, C, D. Smooth or notched (cogged) underside.
Wedge beltA deeper, narrower V than a classic belt. Metric SPZ, SPA, SPB, SPC or imperial 3V, 5V, 8V.
Timing beltTeeth across the underside that mesh with toothed pulleys. Trapezoidal (XL, L, H, T5, T10) or rounded (HTD 3M, 5M, 8M, 14M).
Ribbed / poly-V beltA flat belt with several small V-shaped ribs running along its length. Profiles PH, PJ, PK, PL, PM.

3.Inside, pitch and outside length

A belt has three possible lengths, and different makers quote different ones. Mixing them up is the most common reason for ordering the wrong size.

Outside Pitch Inside Belt loop, side view
The pitch line runs through the belt's tension cords.
LengthMeasured alongUsually used for
Inside (Li)The inner surface of the beltClassic V-belts (A, B, C)
Pitch / datum (Lp, Ld, Lw)The pitch line, through the tension cordsWedge belts (SPZ, SPA), timing belts
Outside (La, Le)The outer surface of the beltImperial narrow belts (3V, 5V), ribbed belts

4.V-belts and wedge belts

Measure the section

  1. Measure the top widthUse callipers across the widest (back) face of the belt.
  2. Measure the heightMeasure the depth from the back face to the bottom of the V.
  3. Match it to the tableWedge belts are noticeably deeper than classic belts with the same top width.
SectionTop width (mm)Height (mm)Length in the code
Z106Inside
A138Inside, in inches
B1711Inside, in inches
C2214Inside, in inches
D3219Inside
SPZ108Pitch, in mm
SPA1310Pitch, in mm
SPB16.313Pitch, in mm
SPC2218Pitch, in mm
3V9.58Outside, inches x 10
5V1613.5Outside, inches x 10
8V25.523Outside, inches x 10

Sizes are nominal. A worn belt will usually measure a little narrower than a new one.

Measure the length

  1. Wrap a tape or string round the outsideUse a flexible tape or non-stretch string, snug and flat against the back of the belt.
  2. Mark where it meetsMeasure the string against a steel rule. This is the outside length.
  3. Convert itUse the table below to get the length your section is sold by.
SectionInside length (Li)Pitch length (Lp)
ZOutside minus approx. 38 mmInside plus approx. 22 mm
AOutside minus approx. 50 mmInside plus approx. 30 mm
BOutside minus approx. 69 mmInside plus approx. 40 mm
COutside minus approx. 94 mmInside plus approx. 58 mm
SPZn/aOutside minus approx. 13 mm
SPAn/aOutside minus approx. 18 mm
SPBn/aOutside minus approx. 22 mm
SPCn/aOutside minus approx. 30 mm

Used belts stretch. If your measurement falls between two standard sizes, the shorter one is usually right. If in doubt, ask us before ordering.

Classic belt codes: the number on an A, B or C belt is its inside length in inches. Multiply by 25.4 for millimetres, so an A42 is about 1067 mm inside.

5.Timing belts

To identify a timing belt you need the tooth pitch, the length (or number of teeth) and the width. Tooth shape matters too: trapezoidal and rounded teeth won't run on each other's pulleys.

  1. Check the tooth shapeLook at the teeth side-on. Trapezoidal teeth have flat tops and angled sides. Rounded (HTD) teeth are curved.
  2. Measure the pitch over 10 teethMeasure from the centre of one tooth to the centre of the tooth 10 along, then divide by 10. This is far more accurate than measuring a single gap.
  3. Count the teethChalk a starting tooth and count all the way round.
  4. Measure the widthMeasure straight across the belt with callipers.
ProfilePitchTooth shapeUnits
MXL2.032 mmTrapezoidalImperial
XL5.08 mm (1/5")TrapezoidalImperial
L9.525 mm (3/8")TrapezoidalImperial
H12.7 mm (1/2")TrapezoidalImperial
T5 / AT55 mmTrapezoidalMetric
T10 / AT1010 mmTrapezoidalMetric
HTD 3M3 mmRoundedMetric
HTD 5M5 mmRoundedMetric
HTD 8M8 mmRoundedMetric
HTD 14M14 mmRoundedMetric
Pitch length = number of teeth x tooth pitche.g. an HTD 8M belt with 100 teeth = 800 mm

Timing belts barely stretch, so counting teeth gives an exact length even on a worn belt.

Watch out: T5 and HTD 5M both have a 5 mm pitch, and XL (5.08 mm) is very close. Check the tooth shape to tell them apart. Imperial widths are shown in hundredths of an inch in the code, so 100 means 1.00 inch (25.4 mm).

6.Ribbed (poly-V) belts

  1. Count the ribsCount the V-shaped ribs across the width of the belt.
  2. Work out the rib pitchMeasure the full width of the ribbed side and divide by the number of ribs.
  3. Measure the lengthMeasure round the outside with a tape or string, as for V-belts. Ribbed belts are sold by effective (outside) length.
ProfileRib pitchTypical use
PH1.60 mmSmall appliances, light drives
PJ2.34 mmPower tools, washing machines, fitness equipment
PK3.56 mmVehicle auxiliary drives
PL4.70 mmIndustrial machinery
PM9.40 mmHeavy industrial drives

The code reads ribs, then profile, then length. For example 8PJ1016 is 8 ribs, PJ profile, 1016 mm long.

7.No old belt? Measure the drive

If the belt is missing or destroyed, you can work out the length from the pulleys.

  1. Set the tensioner to mid-rangeMove the adjustable pulley or motor to the middle of its travel.
  2. Measure the centre distance (C)Measure between the centres of the two shafts.
  3. Measure both pulley pitch diametersLarge pulley (D) and small pulley (d). On V-belt pulleys this is a little less than the outside diameter.
L = 2C + 1.571 (D + d) + (D − d)² ÷ 4CGives the approximate pitch length. Pick the nearest standard size.

Worked example: C = 500 mm, D = 200 mm, d = 100 mm.
2 x 500 = 1000, plus 1.571 x 300 = 471, plus 100² ÷ 2000 = 5. Total: about 1476 mm pitch length.

Tools that help

  • Digital or vernier callipers for section, width and pitch
  • A flexible tape measure or non-stretch string
  • Chalk or a marker for counting teeth
  • A steel rule for checking string lengths

8.Still not sure?

We'll match it for you

Send us the belt code, a clear photo of the belt and its cross-section, and your measurements. Orders placed before 2pm, Monday to Friday, are dispatched the same day.