Help
How to measure belts
Identify and measure V-belts, wedge belts, timing belts and ribbed belts, so you order the right replacement first time.
1.Read the code first
Almost every belt has a reference printed or moulded on its back. If you can read it, it's more reliable than any tape measure, because used belts stretch and wear. Wipe the belt clean and check its full length, as the print is often faint on older belts.
| Example code | Belt type | What it means |
|---|---|---|
A42 | Classic V-belt | A section, 42 inch inside length |
SPZ1000 | Wedge belt | SPZ section, 1000 mm pitch (datum) length |
3V500 | Narrow V-belt (imperial) | 3V section, 50.0 inch outside length |
800-8M-20 | HTD timing belt | 800 mm pitch length, 8 mm tooth pitch, 20 mm wide |
390L100 | Imperial timing belt | 39.0 inch pitch length, L pitch, 1.00 inch wide |
6PK1200 | Ribbed (poly-V) belt | 6 ribs, PK profile, 1200 mm effective length |
Got a code? Type it into the part number search. If it's partly worn off, send us what you can read with a photo and we'll help match it.
2.Identify the belt type
Look at the belt's cross-section and underside. Each type is measured differently, so work this out first.
3.Inside, pitch and outside length
A belt has three possible lengths, and different makers quote different ones. Mixing them up is the most common reason for ordering the wrong size.
| Length | Measured along | Usually used for |
|---|---|---|
| Inside (Li) | The inner surface of the belt | Classic V-belts (A, B, C) |
| Pitch / datum (Lp, Ld, Lw) | The pitch line, through the tension cords | Wedge belts (SPZ, SPA), timing belts |
| Outside (La, Le) | The outer surface of the belt | Imperial narrow belts (3V, 5V), ribbed belts |
4.V-belts and wedge belts
Measure the section
- Measure the top widthUse callipers across the widest (back) face of the belt.
- Measure the heightMeasure the depth from the back face to the bottom of the V.
- Match it to the tableWedge belts are noticeably deeper than classic belts with the same top width.
| Section | Top width (mm) | Height (mm) | Length in the code |
|---|---|---|---|
| Z | 10 | 6 | Inside |
| A | 13 | 8 | Inside, in inches |
| B | 17 | 11 | Inside, in inches |
| C | 22 | 14 | Inside, in inches |
| D | 32 | 19 | Inside |
| SPZ | 10 | 8 | Pitch, in mm |
| SPA | 13 | 10 | Pitch, in mm |
| SPB | 16.3 | 13 | Pitch, in mm |
| SPC | 22 | 18 | Pitch, in mm |
| 3V | 9.5 | 8 | Outside, inches x 10 |
| 5V | 16 | 13.5 | Outside, inches x 10 |
| 8V | 25.5 | 23 | Outside, inches x 10 |
Sizes are nominal. A worn belt will usually measure a little narrower than a new one.
Measure the length
- Wrap a tape or string round the outsideUse a flexible tape or non-stretch string, snug and flat against the back of the belt.
- Mark where it meetsMeasure the string against a steel rule. This is the outside length.
- Convert itUse the table below to get the length your section is sold by.
| Section | Inside length (Li) | Pitch length (Lp) |
|---|---|---|
| Z | Outside minus approx. 38 mm | Inside plus approx. 22 mm |
| A | Outside minus approx. 50 mm | Inside plus approx. 30 mm |
| B | Outside minus approx. 69 mm | Inside plus approx. 40 mm |
| C | Outside minus approx. 94 mm | Inside plus approx. 58 mm |
| SPZ | n/a | Outside minus approx. 13 mm |
| SPA | n/a | Outside minus approx. 18 mm |
| SPB | n/a | Outside minus approx. 22 mm |
| SPC | n/a | Outside minus approx. 30 mm |
Used belts stretch. If your measurement falls between two standard sizes, the shorter one is usually right. If in doubt, ask us before ordering.
Classic belt codes: the number on an A, B or C belt is its inside length in inches. Multiply by 25.4 for millimetres, so an A42 is about 1067 mm inside.
5.Timing belts
To identify a timing belt you need the tooth pitch, the length (or number of teeth) and the width. Tooth shape matters too: trapezoidal and rounded teeth won't run on each other's pulleys.
- Check the tooth shapeLook at the teeth side-on. Trapezoidal teeth have flat tops and angled sides. Rounded (HTD) teeth are curved.
- Measure the pitch over 10 teethMeasure from the centre of one tooth to the centre of the tooth 10 along, then divide by 10. This is far more accurate than measuring a single gap.
- Count the teethChalk a starting tooth and count all the way round.
- Measure the widthMeasure straight across the belt with callipers.
| Profile | Pitch | Tooth shape | Units |
|---|---|---|---|
| MXL | 2.032 mm | Trapezoidal | Imperial |
| XL | 5.08 mm (1/5") | Trapezoidal | Imperial |
| L | 9.525 mm (3/8") | Trapezoidal | Imperial |
| H | 12.7 mm (1/2") | Trapezoidal | Imperial |
| T5 / AT5 | 5 mm | Trapezoidal | Metric |
| T10 / AT10 | 10 mm | Trapezoidal | Metric |
| HTD 3M | 3 mm | Rounded | Metric |
| HTD 5M | 5 mm | Rounded | Metric |
| HTD 8M | 8 mm | Rounded | Metric |
| HTD 14M | 14 mm | Rounded | Metric |
Timing belts barely stretch, so counting teeth gives an exact length even on a worn belt.
Watch out: T5 and HTD 5M both have a 5 mm pitch, and XL (5.08 mm) is very close. Check the tooth shape to tell them apart. Imperial widths are shown in hundredths of an inch in the code, so 100 means 1.00 inch (25.4 mm).
6.Ribbed (poly-V) belts
- Count the ribsCount the V-shaped ribs across the width of the belt.
- Work out the rib pitchMeasure the full width of the ribbed side and divide by the number of ribs.
- Measure the lengthMeasure round the outside with a tape or string, as for V-belts. Ribbed belts are sold by effective (outside) length.
| Profile | Rib pitch | Typical use |
|---|---|---|
| PH | 1.60 mm | Small appliances, light drives |
| PJ | 2.34 mm | Power tools, washing machines, fitness equipment |
| PK | 3.56 mm | Vehicle auxiliary drives |
| PL | 4.70 mm | Industrial machinery |
| PM | 9.40 mm | Heavy industrial drives |
The code reads ribs, then profile, then length. For example 8PJ1016 is 8 ribs, PJ profile, 1016 mm long.
7.No old belt? Measure the drive
If the belt is missing or destroyed, you can work out the length from the pulleys.
- Set the tensioner to mid-rangeMove the adjustable pulley or motor to the middle of its travel.
- Measure the centre distance (C)Measure between the centres of the two shafts.
- Measure both pulley pitch diametersLarge pulley (D) and small pulley (d). On V-belt pulleys this is a little less than the outside diameter.
Worked example: C = 500 mm, D = 200 mm, d = 100 mm.
2 x 500 = 1000, plus 1.571 x 300 = 471, plus 100² ÷ 2000 = 5. Total: about 1476 mm pitch length.
Tools that help
- Digital or vernier callipers for section, width and pitch
- A flexible tape measure or non-stretch string
- Chalk or a marker for counting teeth
- A steel rule for checking string lengths
8.Still not sure?
We'll match it for you
Send us the belt code, a clear photo of the belt and its cross-section, and your measurements. Orders placed before 2pm, Monday to Friday, are dispatched the same day.